Ether2DMX8 is a highly capable DMX router and much more! As a DMX router, it translates Artnet protocol into DMX in/out universes but can also be used as a DMX merger, DMX splitter hub, fail safe device, cue playback, and DMX viewer monitor. Ether2DMX8 is also an M-PC license and therefore a full controller solution.
|
| Features |
- Artnet to DMX conversion
- DMX to Artnet conversion
- 10 Factory Presets
- 10 User Presets
- 99 Cues with Fade Time, Hold Time and Cue Linking
- 8 Switch Inputs
- 8 XLR female 5pins
- DMX Monitor
- DMX and Artnet Test Generator
- Multiple Artnet IP in for backup system
- USB port for backup and firmware updates
|
Physical |
| Length: 288 mm (11.3 in.) |
| Width: 482.2 mm (19.0 in.), 19-inch rackmount |
| Height: 43.6 mm (1.7 in.),1U |
| Weight: 3.6 kg (7.9 lbs.) |
Control/User Interface |
| Front panel display with 4-button control menu |
| 1 x dual-color LED per port |
| Mouse & keyboard input |
| Remote web access |
| DMX viewer for any physical incoming or outgoing DMX port |
Hardware |
| 520 MHz processor for fast, synchronized DMX output, latency virtually zero |
| Ethernet: |
| Artnet-compliant, Artnet II-compliant |
| ACN-ready |
| Built-in webpage for quick access and remote setup |
| 10/100 Mbit connection |
| 8 ports: |
| Configurable as input or output |
| Opto-isolated circuit for each port |
| User-definable DMX timings for each port |
| Each port set as output can be set to constantly repeat the last received DMX frame, or only to output new frames |
| RDM-ready |
| Dual-color LED for each port |
| 8 open-contact inputs: |
| Inputs transmit ArtNet-compatible contact closures on the network |
| Contact closures can trigger factory and user presets and start cue playback |
Software |
| 10 user presets for device configuration |
| Maxxyz, Maxedia use preset with auto-IP address setting |
| Presets for DMX Hub and Spitter functionality |
| Mergeable setup where multiple inputs are routed in LTP, HTP to one output |
| Ports assignable to input or output |
| Ports routable to/from internal ports or to/from any DMX universe on Artnet |
| Port routing triggerable by contact closure through the use of user presets |
| Ports' DMX channel ranges configurable |
| Merger modules routable between inputs & outputs and/or Artnet universes |
| Channel ranges can be put in LTP/HTP, copy or fixed value from other channels |
| Auto or manual IP addressing |
| Tracking backup function: automatic handover to another Artnet signal if one Artnet signal fails |
| DMX and Artnet test pattern generator |
| Artnet broadcast and unicast compatible |
| Configuration files loadable/storable on USB memory sticks |
| Firmware upload via USB memory stick |
Construction |
| Housing: Steel and aluminum |
| Finish: Electrostatic powder-coated |
Installation |
| 19-inch rackmount (1U) |
Connections |
| 10/100 base-T ethernet port: Neutrik locking RJ45 Ethercon socket |
| DMX in/out ports: 8 x 5-pin female XLR |
| Keyboard: USB or PS2 |
| Mouse: USB or PS2 |
| Backup, software upload: USB |
| Monitor: VGA 15-pin |
| AC power input: 3-pin IEC male socket |
| AC power throughput: 3-pin IEC female socket |
Electrical |
| AC power: Auto-ranging 100 - 240 VAC nominal, 50/60 Hz |
| Main fuse: 2 x 500 mA T (slow-blow) |
Typical Power and Current |
| 100 V, 60 Hz: 220 mA |
| Measurements made at nominal voltage. Allow for a deviation of +/- 10%. |
Ordering Information |
|
| |
.jpg){kind=small}
.jpg){kind=small}
.jpg){kind=small}
.jpg){kind=small}
